Amer Networks SS2R48G4I Manual de usuario Pagina 162
- Pagina / 198
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SS2R24G4i/SS2R48G4i
151
17.3 Port Channel Example
Scenario 1 Configuring Port Channel in LACP.
S1
S2
Fig 17-2 Configuring Port Channel in LACP
Example The switches in the description below are all SS2R24/48G4i switch switch and as shown in
the figure, ports 1, 2, 3 of Switch1 are access ports that belong to vlan1. Add those three ports to
group1 in active mode. Ports 6, 7, 8 of Switch2 are trunk ports that also belong to vlan1,and allow all.
Add these three ports to group2 in passive mode. All the ports should be connected with cables
The configuration steps are listed below
Switch1#config
Switch1 (Config)#interface eth 0/0/1-3
Switch1 (Config-Port-Range)#port-group 1 mode active
Switch1 (Config-Port-Range)#exit
Switch1 (Config)#interface port-channel 1
Switch1 (Config-If-Port-Channel1)#
Switch2#config
Switch2 (Config)#port-group 2
Switch2 (Config)#interface eth 0/0/6
Switch2 (Config-Ethernet0/0/6)#port-group 2 mode passive
Switch2 (Config-Ethernet0/0/6)#exit
Switch2 (Config)# interface eth 0/0/8-9
Switch2 (Config-Port-Range)#port-group 2 mode passive
Switch2 (Config-Port-Range)#exit
Switch2 (Config)#interface port-channel 2
Switch2 (Config-If-Port-Channel2)#
Configuration result
Shell prompts ports aggregated successfully after a while, now ports 1, 2, 3of Switch 1 form an
aggregated port named “Port-Channel1”, ports 6, 7, 8 of Switch 2 forms an aggregated port named
“Port-Channel2”; configurations can be made in their respective aggregated port configuration mode.
- USER MANUAL 1
- Caution 3
- Electronic Emission Notices 3
- Preface 4
- CONTENTS 5
- Chapter 1 Switch Overview 12
- 1.1.3 Main Features 14
- 1.2 Technical specifications 15
- 1.3 Physical Specifications 16
- 1.4 Product appearance 16
- 1.4.3 Status LEDs 17
- 2.1 Installation Notice 19
- 2.1.1.3 Power Supply 20
- 2.1.2 Installation Notice 21
- 2.1.3 Security Warnings 22
- 2.2 Installation Preparation 22
- 2.3 Hardware Installation 23
- 2.3.1 Installing the Switch 23
- 2.3.2 Connecting Console 23
- Caution! 24
- 3.1 Setup Configuration 26
- 3.2 Main Setup Menu 26
- 3.3 Setup Submenu 26
- 3.3.4 Configuring Web Server 28
- 3.3.5 Configuring SNMP 28
- Chapter 4 Switch Management 31
- 4.1.2 In-band Management 34
- Switch#config 35
- 4.1.2.2 Management via HTTP 36
- 4.2 Management Interface 37
- 4.2.1 CLI Interface 38
- 4.2.1.1.2 Admin Mode 39
- 4.2.1.1.3 Global Mode 39
- 4.2.1.1.4 Interface Mode 39
- 4.2.1.1.5 VLAVLAN Mode 40
- 4.2.1.1.7 ACL Mode 40
- 4.2.1.2 Configuration Syntax 40
- 4.2.1.3 Shortcut Key Support 41
- 4.2.1.4 Help Function 42
- 4.2.1.5 Input Verification 42
- 4.2.2 Web Interfac 43
- 5.1.1 clock set 45
- 5.1.2 config 45
- 5.1.3 exit 45
- 5.1.4 help 46
- 5.1.5 ip host 46
- 5.1.6 ip http server 46
- 5.1.7 hostname 46
- 5.1.8 reload 46
- 5.1.10 language 47
- 5.1.11 web-user 47
- 5.1.12 write 47
- 5.1.9 setup 47
- 5.1.13 show cpu usage 48
- 5.2.1 Ping 48
- 5.2.2 Telnet 48
- 5.2.2.3 Commands for Telnet 50
- 5.2.2.3.2 monitor 50
- 5.2.2.3.3 telnet 50
- 5.2.3 SSH 51
- 5.2.3.3 Commands for SSH 52
- 5.2.3.3.1 ssh-server enable 52
- 5.2.3.3.2 ssh-user 52
- 5.2.3.3.3 ssh-server timeout 53
- 5.2.3.3.6 monitor 53
- 5.2.3.5.1 show ssh-user 54
- 5.2.3.5.2 show ssh-server 54
- 5.2.3.5.3 debug ssh-server 54
- 5.2.4 Traceroute 55
- 5.2.5 Show 55
- 5.2.6 Debug 57
- 5.4 SNMP Configuration 59
- 5.4.1 Introduction To SNMP 59
- 5.4.2 Introduction to MIB 60
- 5.4.3 Introduction to RMON 61
- 5.4.4 SNMP Configuration 61
- 5.4.6 SNMP Troubleshooting 64
- 5.4.6.1.2 show snmp status 65
- 5.4.6.1.4 show snmp user 66
- 5.4.6.1.5 show snmp group 66
- 5.4.6.1.6 show snmp view 66
- 5.5 Switch Upgrade 67
- 5.5.1 BootROM Upgrade 68
- 5.5.2 FTP/TFTP Upgrade 69
- 5.6.1.1 Log Output Channel 72
- 5.6.4.1.1 show channel 76
- 5.7 Classified Configuration 77
- 5.8 Port Isolation 77
- Chapter 7 Port Configuration 82
- 7.2.3.3 Mirror Port Examples 85
- 7.2.3.4.1 show monitor 86
- 7.2.3.4.2 debug mirror 86
- 7.4 Port Troubleshooting 88
- 8.1.1 Obtaining MAC Table 89
- 8.1.2 Forward or Filte 90
- 8.2.2 mac-address-table 91
- 8.4 Troubleshooting 92
- 8.4.2 Troubleshooting 93
- 8.5.1 MAC Address Binding 93
- 8.5.1.3.2 show port-security 95
- Chapter 9 VLAN Configuration 97
- 9.2 VLAN Configuration 98
- Trunk Link 100
- SS2R24G4i/SS2R48G4i 101
- 9.5 VLAN Troubleshooting 105
- 10.1 INTRODUCTION TO RSTP 107
- 10.2 RSTP CONFIGURATION 108
- 10.4 RSTP Troubleshooting 111
- 10.4.2 RSTP TROUBLESHOOTING 112
- Chapter 11 IGMP Snooping 113
- 11.3 IGMP Snooping Examples 115
- 12.3 Multicast VLAN Examples 120
- 13.1 DCSCM Introduction 122
- 13.2 DCSCM Configuration 122
- 13.3 DCSCM Typical Examples 125
- 13.4 DCSCM Troubleshooting 126
- 14.1 Introduction to 802.1x 128
- 14.2 802.1x Configuration 129
- 10.1.1.1 133
- 10.1.1.2 133
- Radius Server 133
- 10.1.1.3 133
- 14.4 802.1x Troubleshooting 134
- Chapter 15 ACL Configuration 139
- 15.3 ACL Configuration 140
- 15.4 ACL Example 150
- 15.5 ACL Troubleshooting 153
- 15.5.2 ACL Troubleshooting 154
- Chapter 16 AM Configuration 156
- 16.4 AM Examples 157
- 16.5 AM Troubleshooting 158
- 16.5.2 AM Troubleshooting 159
- 17.3 Port Channel Example 162
- 18.1 Introduction to DHCP 167
- 18.3 DHCP Troubleshooting 171
- 18.3.2 DHCP Troubleshooting 174
- Scanning 180
- 21.1 Commands for SNTP 182
- 21.1.1 sntp server 182
- 21.1.2 sntp polltime 182
- 21.1.3 sntp timezone 182
- 21.1.4 show sntp 183
- 21.1.5 debug sntp 183
- Chapter 22 QoS Configuration 185
- 22.1.2 QoS Implementation 186
- 22.1.3 Basic QoS Model 186
- 22.2 QoS Configuration 187
- 22.3 QoS Example 190
- 22.4 QoS Troubleshooting 192
- 23.1 Layer3 Interface 196
- 23.2 ARP 197
- 23.2.1 Introduction to ARP 197
Relacionado con productos y manuales para Los conmutadores de red Amer Networks SS2R48G4I
(13 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.162 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales