Amer-networks WS6028 Web GUI Manual de usuario Pagina 28
- Pagina / 105
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Basic Management Configuration Chapter 5 Networks
5-5
5.5 Enable Dist-tunnel Mode
Click the dist-tunnel mode on-off button to enable it as below:
5.6 Client QoS
The client QoS controls the rate and access of the client through the network. There
are three options: 1. Client QoS bandwidth limit up and down; 2. Client QoS access
control up and down; 3. Client QoS DiffServ policy up and down.
Enable the global on-off of client QoS first before using this option. In WLAN
configurationsystem config, choose the “client-QoS global mode” and apply to enable
the global on-off as below:
After selecting the client QoS option under the global mode, select the appropriate
QOS option. Choose the bandwidth limit up option and input the value to configure it; and
use the same for the bandwidth limit down. Click the client QoS access control up/down
button, and the configured ACL can be chosen from the drop-down box (ACL
configuration is viewed in the CLI Switch Manual). Choose the client QoS DiffServ policy
up/down button, the configured DiffServ policies can be selected (DiffServ configuration is
viewed in the CLI Switch Manual) After configuration, click “OK” to complete the QoS
configuration.
- WS6028 Web GUI Manual 1
- Content 2
- CHAPTER 18 6
- CHAPTER 19 6
- Chapter 1 Web Management 8
- Fig 1-5 10
- 1.2.1 Login AC Switch 11
- Fig 1-7 12
- Fig 1-8 12
- 1.2.3 Menu Introduction 13
- Chapter 2 Dashboard 15
- 2.3 Device Info 16
- 2.4 Support 16
- Chapter 3 Fast Config 17
- 3.3 Network Config 18
- 3.3.1 SSID 18
- 3.3.2 Security 18
- 3.3.2.2 WPA/WPA2 19
- Chapter 4 System Config 20
- 4.3 AP Authentication Mode 21
- 4.4 AP Validation Method 21
- 4.6 Radius Accounting Mode 22
- 4.7 Radius Accounting Server 22
- 4.8 Client-QoS Global Mode 22
- 4.9 Country Code 22
- 4.10 Peer Group ID 23
- 4.11 Cluster Priority 23
- Chapter 5 Networks 24
- 5.2.3 WEP 802.1x 25
- 5.2.4 WPA Personal 26
- 5.2.5 WPA Enterprise 26
- 5.3 Configure VLAN 27
- 5.4 Mac Authentication 27
- 5.5 Enable Dist-tunnel Mode 28
- 5.6 Client QoS 28
- Chapter 6 AP Management 30
- 6.1.2 AP Config 31
- 6.1.3 Radio 31
- 6.1.4 VAP 32
- 6.1.5 QoS 33
- 6.1.6 TSPEC 34
- 6.2 Copy AP Group 34
- 6.3 Apply AP Group 35
- 7.1 Radius Configuration 36
- 7.1.1 Global Configuration 36
- Configuration 37
- 7.1.4 Radius Group Manage 37
- 7.1.5 Radius Configuration 38
- 7.2 LDAP Configuration 38
- Chapter 8 Discovery 40
- Chapter 9 Provisioning 42
- 9.2 Switch Provisioning 43
- 9.3 Mutual Authentication 43
- Chapter 10 WIDS Security 45
- 10.2 Client Configuration 46
- 10.3 Known Client 47
- Chapter 11 Captive Portal 49
- Chapter 12 Config Push 54
- 13.1 AP Image Auto Upgrade 56
- Chapter 14 Load Balance 60
- Identifier (OUI) 65
- Chapter 17 Trap and Syslog 66
- 17.1.2 Captive Portal 67
- 17.2 Syslog Configuration 67
- Chapter 18 Monitor 68
- 18.1.1.2 Cluster Controller 70
- 18.1.1.4 Global Statistics 71
- 18.1.1.6 TSPEC Status 71
- 18.1.1.7 TSPEC Statistics 71
- 18.1.2.1 AC Selection List 73
- 18.1.2.3 AC Statistics 74
- 18.1.2.4 TSPEC Status 74
- 18.1.2.5 TSPEC Statistics 74
- 18.2 AP 75
- 18.2.1 Basic AP Information 75
- 18.2.2 AP Detail 76
- 18.2.2.2 Radio Detail 77
- 18.2.2.3 Neighbor APs 77
- 18.2.2.4 Neighbor Clients 78
- 18.2.2.5 VAP 78
- 18.2.2.6 VAP TSPEC 78
- 18.2.3 Failure AP List 79
- 18.3 Wireless Client 79
- 18.3.3 Detected Client List 81
- 18.4 RF Scan 84
- 18.4.1 AP RF Scan Status 84
- 18.4.2 AP RF Scan Detail 84
- 18.4.2.1 AP RF Scan Status 85
- Chapter 19 Management 87
- 19.1.4 Basic Configuration 89
- 19.2 SNMP Configuration 91
- 19.2.1 SNMP Authentication 91
- 19.2.1.2 Groups 92
- 19.2.1.3 Views 93
- 19.2.2 SNMP Management 94
- 19.2.3 Community Managers 94
- 19.2.5 SNMP Statistics 95
- 19.3 SSH Management 96
- 19.3.1 Switch on-off SSH 96
- 19.3.2 SSH Management 96
- 19.4 Firmware Update 97
- 19.4.1 TFTP Client Service 98
- 19.4.2 TFTP Server Service 99
- 19.4.3 FTP Client Service 100
- 19.4.4 FTP Server Service 101
- 19.5.1 Telnet Server State 102
- Connection 102
- 19.6.1 Debug Command 103
- 19.6.2 Others 104
© 2020, manymanuals.es. Todos los derechos reservados | 0.091 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales